Roof coatings9 min read

Can an EPDM Roof Be Coated Instead of Replaced? What the Specs Require Before Silicone Goes On

Usually yes, if the membrane is dry, still bonded and passes an adhesion test. This post walks through what GAF, Gaco and Johns Manville each require before silicone goes on EPDM, what happens at the seams, when the answer is a re-roof, and how A-1 restored a 20-year-old EPDM school roof in Colome, South Dakota.

ByA-1 Roofing

In short

Yes, if the membrane is dry, still bonded and passes an adhesion test. GAF's EPDM specification requires a moisture survey, wet areas replaced, seams repaired with like materials, a primer and an adhesion test before silicone goes on; Gaco strongly recommends the survey and tests. A-1 restored a 20-year-old EPDM school roof in Colome, South Dakota in 11 working days.

Can an EPDM roof be coated instead of replaced?

Yes, and the major coating makers publish specifications written for it. GAF's quick specification for its Unisil HS silicone over EPDM (dated September 2018, so a legacy benchmark) offers a 10-year warranty at 1.5 gallons per square, 15 years at 2.0 gallons and 20 years at 2.5 gallons, which works out to about 23, 31 and 38 dry mils. A square is 100 square feet.

The coating does not turn a failed roof into a good one. Every specification below starts from the same place: the EPDM underneath has to still be doing its job. The coating then takes over the surface that weathers, and the membrane, insulation and deck stay where they are.

That is the trade an owner is weighing. A re-roof removes everything down to the deck and starts over. A coating keeps what is sound and adds a new surface on top. The rest of this post is about how to tell which roof you have.

Which EPDM roofs are candidates for a coating?

Dry ones. GAF's specification makes a moisture survey a requirement and says to remove and replace all wet areas before the membrane is repaired, cleaned and primed. It also requires the roof to be clean, dry and tight, and it notes a maximum slope of 2:12 for the coating.

Drained ones. Johns Manville's coatings application guide (2019, a legacy benchmark) cites NRCA's guideline that the surface must have positive drainage, which it defines as no water standing 48 hours after precipitation stops. A coating does not fix a low spot. Water that ponded on the bare EPDM will pond on the silicone too.

Bonded ones. A fully adhered membrane that has pulled away from the deck, or seams that have opened, have to be repaired before the coating, and the repair has to be with like materials. Where that repair work covers most of the roof, the numbers start to favor replacement, which is the last question in this post.

Not too thin, too old or too cold inside. Gaco's current single-ply specification limits its silicone to membranes at least 45 mils thick and less than 25 years old. It disqualifies a reinforced membrane worn down until its scrim shows, and it does not recommend the silicone on cold storage buildings.

Johns Manville approves its silicone over aged EPDM that is mechanically attached or adhered, and Gaco's single-ply specification excludes ballasted systems. Gaco does publish a separate specification for coating ballasted EPDM in place, for membranes aged 30 years or less. The ballast is moved in stages, never all at once, a nuclear or infrared moisture scan is required, and before the warranty is issued the owner signs an overburden waiver that provides for removing and replacing the ballast during the warranty period so the coating can be inspected or repaired. A-1 considers only fully adhered or mechanically fastened single-ply roofs for restoration.

Does EPDM need a primer before silicone?

Usually. GAF's specification says to prime with two products, Adhere-It II and Unisil Primer. Johns Manville says its Single Ply Primer must be used with EPDM and TPO under its silicone. Gaco's current single-ply specification for its S20 silicone calls for a primer if adhesion testing shows the need, and always on areas repaired with new membrane. Gaco's adhesion procedure says that when a specification calls for a primer, the primer has to be part of the adhesion test as well.

At Colome Elementary, A-1 used Gaco's E5320, a two-part epoxy primer, across the whole field of the roof after washing it.

Cleaning comes first, and it is more than a rinse. Johns Manville lists scrubbing with a power wash or detergent for EPDM and warns that a surface not completely cleaned and dried will adhere poorly, which can lead to delamination and blistering. Colome's roof was washed with Gaco Wash and high-pressure washers to take off 20 years of oxidation before the primer went on.

A-1 is starting to use a primerless silicone on EPDM, Gaco's S-4200. Where a roof needs a primer, it uses Gaco's E5320 epoxy primer, the same one used at Colome.

How do you know the coating will stick to the EPDM?

Gaco's answer is to test it on the roof before the job is bid. Gaco's adhesion testing procedure (revised June 2020, a legacy benchmark) strongly recommends adhesion tests before bidding, at a rate of one test per 10,000 square feet with a minimum of two. It says to pick areas that show more pronounced degradation and to run wet adhesion tests in areas prone to ponding.

The tests are small patches. Johns Manville's version is a strip of polyester fabric set in primer and coating, cured, then pulled off with a scale while someone records the peak force. A pass is at least 2 pounds per inch of fabric width. JM requires peel tests at each distinct substrate type, surfacing or age on the roof, with a minimum of five at various locations. GAF sets its minimum at 2.0 pounds per linear inch.

A failed test is not the end of the road. Gaco says to repeat it with an appropriate primer. Johns Manville says a failing test calls for different cleaning and preparation, or means the roof does not qualify for a coating. For a warranted Gaco job, the test results go to Gaco with the pre-installation notice.

On Colome Elementary, a Gaco representative approved the roof before work started, which the full factory warranty required.

What happens to the seams on a coated EPDM roof?

They get repaired, then reinforced. GAF's specification says to repair seams, penetrations, flashings, curbs and terminations with like materials first. After that, every loose seam is three-coursed: a layer of silicone flashing grade, a fabric, and more flashing grade, which GAF puts at 2.5 gallons per square and 44 dry mils. Seams that are still tight get flashing grade only, at 1.25 gallons per square and 19 dry mils.

Colome's seams had failed. A-1 cut back the delaminated and saturated areas and rebuilt them with like EPDM, then reinforced the seams and details with polyester mesh set in Gaco's S-20 silicone and its SF-2000 fibered silicone before the field coat.

What did coating a 20-year-old EPDM roof look like on a real school?

Colome School District asked A-1 to assess every roof on its K-12 campus. The elementary building's fully adhered EPDM came back oldest and worst: 20 years old, failing seams and a heavily oxidized surface.

In 2021 a four-person A-1 crew restored the 15,067-square-foot roof in 11 working days, in this order. A Gaco representative approved the roof. A-1 found the wet areas by eye and confirmed them with cores. The delaminated and saturated areas were cut back and rebuilt with like EPDM. The roof was washed with Gaco Wash and high-pressure washers. Gaco E5320 epoxy primer went down across the field. Seams and details were reinforced with polyester mesh in silicone. About 40 mils of Gaco S20, a 100 percent silicone, went over the whole roof.

The roof is warranted leak-free for up to 20 years. Apart from the areas cut out and rebuilt, the existing roof stayed in place.

At A-1's most recent inspection, Colome's roof was performing well, with no leaks and no callbacks. No recoat is planned before 2041. Across all its restoration systems, over metal, single-ply and asphalt roofs and as recoats, A-1 estimates it has restored between 2 and 3 million square feet of roof.

How much does coating an EPDM roof save compared with replacing it?

A-1's case study for Colome Elementary puts the cost at half to two-thirds of a re-roof. That range is A-1's own estimate for the job; the case study does not record a re-roof bid to compare it with. For published figures, the Commercial Roof Guide's 2026 cost guide (updated March 2026) puts silicone coating at $2.50 to $4.50 per square foot installed, applied at 20 to 30 mils, and a new EPDM roof at $5.50 to $8.50, with tear-off adding $1.25 to $2.50. Those are national industry estimates, and the coating figure is for a thinner coat than the roughly 40 mils on Colome.

The savings shrink as the repair list grows. Each wet area that has to be removed and replaced, and each loose seam that has to be three-coursed, adds labor and material before the field coat goes down. That is why GAF and Gaco put the moisture survey and the adhesion tests ahead of the coating, and why Gaco recommends running the tests before bidding.

When should an EPDM roof be replaced instead of coated?

When the specifications rule it out. That happens when the adhesion tests keep failing after priming and different cleaning. And it happens when the roof cannot be made to drain, so water would sit on the coating for days after every storm.

It also happens when the wet areas are most of the roof. GAF's specification says to remove and replace every wet area. Past a point, removing and replacing the wet areas is a re-roof done one piece at a time.

A-1's rule of thumb: when 20 percent or more of a roof's insulation is compromised, the roof should be re-roofed. Where several layers are wet down to the deck, 20 percent is too high a cutoff, because the cost of removing the wet material overtakes the savings of a restoration.

If you are not sure which side of the line your roof is on, start with an inspection. A-1's inspections include drone infrared scans for wet insulation. That is how the Colome job started: the district asked A-1 to assess every roof on its K-12 campus.

What does this post not tell you?

This post summarizes published manufacturer documents (GAF's Unisil HS over EPDM quick specification, September 2018; Gaco's adhesion testing procedure GW-GI-1-3, revised June 2020; Johns Manville's coatings application guide RS-2393, 2019; Gaco's single-ply specification SP-S20-38-20, revised May 2026; Gaco's ballasted EPDM specification EPDM-BAL-S20-10, revised January 2024), a 2026 industry cost guide and one A-1 project. The GAF, Johns Manville and Gaco adhesion documents are legacy benchmarks and may have been revised since; Gaco's single-ply specification is current as of May 2026. Specifications and warranties belong to specific manufacturer systems, so the one on your bid is the one that applies. This is not an engineering assessment of any roof, and neither this post nor A-1 Roofing guarantees how a coating will perform on a given building.

Questions owners ask next

Can a new EPDM roof be coated right away?
Not under Johns Manville's guide, which says EPDM, TPO and PVC membranes need to have aged at least one year before any coating is applied.
How late in the year can an EPDM roof be coated in South Dakota?
GAF's specification says to apply at 40°F and rising, with no rain, dew, fog or freezing temperatures in the forecast for 24 hours, and it recommends a surface temperature of 110°F or less. A-1's post on cold-weather limits covers how that plays out in the Upper Midwest's shoulder months.
Do drains, curbs and penetrations get coated too?
Yes. GAF's specification has a separate step to treat all roof penetrations, drains, curbs and scuppers before the field coat, after the membrane repairs and the primer.
Can an acrylic coating go on EPDM instead of silicone?
Not under Johns Manville's guide. Its substrate chart approves JM's acrylic coating over built-up, modified bitumen, PVC and TPO roofs but leaves EPDM off, while its silicone is approved over aged EPDM. Check the substrate chart for whichever coating is on your bid.
Does coating an EPDM roof affect the membrane's own warranty?
It can. The EPDM Roofing Association's FAQ (June 2018) says that before latex-based paint goes on EPDM, the EPDM manufacturer should be contacted to ensure compatibility and continuation of warranty coverage. If the membrane is still under its own warranty, ask its manufacturer before any coating goes on. A coating system carries its own manufacturer's warranty, as Colome's does.
Does it matter if the roof has had patches over the years?
It can. Johns Manville requires its peel tests at each distinct substrate type, surfacing or age on the roof, so an EPDM roof with patches of a different age or material may need its own set of tests in those areas.

Related on this site

Sources

  1. GAF — Unisil HS & Unisil HS II over EPDM, quick specification UH-4 (September 2018, legacy benchmark; hosted by a distributor): moisture survey, 2.0 PLI adhesion, Adhere-It II and Unisil Primer, 10/15/20-year rates
  2. Gaco — GW-GI-1-3 Adhesion Testing Procedure (revised June 2020, legacy benchmark): one test per 10,000 ft², minimum two, before bidding
  3. Johns Manville — RS-2393 JM Coatings Application Guide (2019, legacy benchmark): one-year aging, Single Ply Primer on EPDM, five peel tests at 2 lb per inch
  4. Gaco — SP-S20-38-20 GacoFlex S20 Series over Single-Ply (revised May 2026): membrane at least 45 mils and under 25 years old, ballasted excluded, not for cold storage, moisture survey strongly recommended, primer if adhesion testing shows the need
  5. Gaco — EPDM-BAL-S20-10 GacoFlex S20 Series over Ballasted EPDM (revised January 2024): membranes aged 30 years or less, ballast moved in stages, nuclear or infrared scan required, overburden waiver
  6. Commercial Roof Guide — Commercial roof cost (updated March 2026): silicone coating $2.50–$4.50 per sq ft at 20–30 mils, EPDM $5.50–$8.50, tear-off $1.25–$2.50 (industry estimates)
  7. EPDM Roofing Association — Can EPDM be coated or painted? (FAQ, June 3, 2018)
  8. A-1 case study — Colome Elementary School, Colome SD